What are some Troubleshooting tips for my dryer?

Dryer Troubleshooting Tips

Whenever anything doesn't work properly, it's frustrating and we get it. If this is your first time experiencing troubles with your dryer, you're probably unsure where to even start. Getting your dryer repaired and back up and working is critical to keeping the moisture out to protect your piping, tools and equipment. First thing, check the cooler on the air compressor. If the inlet air temperature is too high going into the air dryer, it will over-work the dryer and it will never reach its dewpoint temperature. If the inlet air temperature is fine, then continue by checking the below items.

Below are a few items to consider if you're dryer starts acting up. For starters, always put safety first and remove the power source to the dryer before troubleshooting or attempting repairs. Also, to minimize any further damage to the air dryer.

1. Heat exchanger coils are dirty

The first thing you should be looking at if your air dryer isn't performing. If your coils are dirty, your air dryer isn't getting proper air flow. The dirty lint blocks and traps the air. Time to clean! Use a soft cloth or brush to clean dirt from the refrigeration condenser coil to allow free passage of air. The condenser may be blown clean with compressed air or, if heavily contaminated, washed with mild detergent and water.

2. Does the Fan Run/Operate?

If your have the dryer turned on and your fan does not, this is a big deal! If the fan isn't pushing air through the coils, there is no way to cool your air. Below are a few things to consider what may be causing this to happen. - Motor shortage or burnt out motor - Failed contactor - Shorted or burnt wires - Blown fuse - Bad fan pressure switch or controller

3. Condensate in the Piping

If you have moisture in your pipes that could mean 1 of 3 things. The dryer is working outside of it's rating, there is bad conditions of condensation, OR the condensate drain discharge is not working properly. Few items to try: - Check inlet air flow rate and temperature to ensure they are properly (within design parameters) working: - Check the room temperature (same as above) - Clean the condenser - Check pressure switch/fan operation - Check your coalescent filter drains

*Check the Drain Function

If your condensate draining isn't performing it pushes all the condensate collected back into the system. This may push the moisture back into the air compressor or into the next stage causing premature wear on your tools or equipment. Remember if your drain has failed, you'll have plenty of water downstream to help you with indicating the problem. Proper functioning and life of the drain are highly dependent on correct maintenance. Here are a few tips: - Clean the filter as often as possible (weekly) - Clean the filter in case of malfunctioning / condensate in the lines - Check the floating device position - Install drain wear kit at least once per year (part # 2200902017)

4. No Compressed Air Passing Through the Dryer Outlet

If you aren't getting any air through the dryer outlet, most likely the heat exchanger is frozen inside. Some ice is normal, but if frozen you need to take faction fast. How does something like that happen? Here's a few common reasons: 1. By-pass broken / out of calibration: If this happens, ice builds on the coils and acts as a type of insulation, further compounding the problem and allowing ice to build up even further. 2. Room temperature too low: Room temperature can not be below 32 degrees Fahrenheit and a dryer should not run lower than 35 degrees Fahrenheit. 3. Refrigerant leaks in the circuit: As the volume of circulating refrigerant declines below specifications, refrigerant temperature initially drops below freezing. Low refrigerant usually indicates a leak in the system that must be tracked down by a professional utilizing leak detection equipment, then properly sealed. Simply topping up a low refrigerant level by adding more without pinpointing and fixing the leak is not a competent repair. If ice accumulation on the coil extends beyond the dimensions of the condensate drip pan beneath the air handler, be ready with containers to catch the dripping water and prevent water damage as the ice melts.

5. Incorrectly sized Dryer

Sizing a dryer can be tricky if you haven't done this before. Having an undersized dryer can lead to poor air quality and overworking your dryer while an over-sized dryer can waste electricity. It’s best to make sure you’ve got one sized correctly for your installation. If you aren’t sure if your dryer is sized correctly, contact us for help.

Still have Questions? We are here to help!

Note that the location of the compressors and dryers can make a big difference in dryer performance. The cooler the air going into the compressor, the lower the dryer inlet temperature. If the compressor room is hot, consider moving the dryer to another, cooler location to boost its effectiveness.

Do you have an idea for our #expertcorner?Β Let us know!

Useful links:

Book Your Compressor Service

Who we are and how Ash Air can help your business!

Ash Air has been around in New Zealand since 1979, and we’ve grown into a nationwide company with international support and a reputation for quality and reliability.We look after all things compressed air for your business!

  • Reciprocating, Screw, air compressors
  • Vacuum pumps
  • Nitrogen
  • An extensive line of air treatment components

Ash Air's range of Chicago Pneumatic, Alup, Pneumatech, and Quincy compressors are used extensively around the world in industries ranging from oil and gas to food, automotive and farming, and we bring you these world class compressors here in the land of the long white cloud.Our technicians are compressed air equipment experts and are dedicated to addressing customer needs. Supported by a 13 locations nationwide, Ash Air offers one of the widest selections of compressed air equipment and parts available today in New Zealand.

Reliability and Efficiency

With Ash Air compressors, you can count on reliability and high performance for even the most demanding applications. We focus our efforts on the following:

  • Increasing uptime
  • Reducing unexpected repairs
  • Reducing energy consumption
  • Improving the cleanliness of compressed air


Talk to the team today:  CONTACT US CONTACT US

Read more from our #expertcorner


Just like any other equipment, a compressed air installation also requires the necessary maintenance work during its entire lifespan. Even though maintenance costs are only about 5 to 10% of a machine's annual operating costs, failure to budget for maintenance can have potentially disastrous consequences. …


The air dyer is one of the most ignored cooler in the system. A dirty condenser will cause water in the lines, or worse it will cause complete dryer failure. …


Using nitrogen is not about fully replacing CO2, but it can reduce their consumption of CO2 by close to 70%. Using nitrogen is about sustainability. Creating your own nitrogen is easy and will reduce the use of a greenhouse gas, which is better for the environment. It will also save you money as early as month one adding that savings to your bottom line. …


A question that is occasionally asked by our customers to Ash Air is 'what is the cost of compressed air?'Β  This article looks at the product costs involved with compressed air, as well as minimising the energy cost of compressors and cost allocation. When looking at these factors, we need to realise what causes dropped efficiency of your compressor, leading to increased costs of compressed air. …


You may have great fall protection measures in place to keep employees safe when working at height, but what about their co-workers below? Dropped tools and other falling objects are a major hazard – and one that isn’t always fully addressed.Β  …


Providing a safe working environment for operators is essential, especially when using pneumatic tools and compressed air. If there is a failure in the air network and the hose is not adequately clamped, the resulting whiplash could be devastating. Failure to follow best practice can result in injuries, associated production downtime and decreased productivity. …


A common questions asked is why do I need an air dryer for my compressor? Typically, air compressors produce water, and although the water can be drained, there can still be aerosol and vapour droplets that are present. This is because water cannoet be compressed. Water can damage your compressor by corroding the valves, pipes and machinery controls, which will cost you time and money to resolve. In the long run, the cost of a new compressor is a small price to pay compared to the loss of production that could potentially arise due to water damage in your compressor.





…


Air compressors can fail for an assortment of different reasons: Normal wear and tear, lifespan and age of the unit, poor maintenance, power surge, install issues are just a few the come to mind. Check out this blog to find out our top 7 tips to ensure your compressor is looked after!  …


That cold, rainy, and in some places icey New Zealand winter is upon us, and with the following air compressor tips, your air system will be prepared with the preferred temperatures, despite the weather outside. Regardless of whether or not it actually snows or freezes up where you live, most winterisation service recommendations are also basic, solid maintenance procedures that will help extend the life and operational efficiencies of air compressors regardless of whether you live in Queenstown or Northland. …


If you're wondering what an air compressor actually is, you've come to the right place. Simply, air compressors convert power in to air that is pressurised which is then used to power air tools such as spray guns. Air compressors are used in a wide range of applications, so naturally if you want one that will be designed for spray painting your vehicle, you want a compressor specifically made for spray guns! This way your compressor will be able to provide the right amount of power to perform the job. …


Compressed air plays a fundamental role in industrial activities. Depending on the type of application, the energy cost of producing compressed air can be very high. Below are some tips to save on you compressor bill. …


Air Compressors are essential tools in a variety of industrial settings. No matter what industry you are in having a reliable air compressor can be a crucial part of getting the job done efficiently. However, like an investment, air compressors require upkeep and maintenance, and eventually will need to be upgraded. But how do you know when it’s time to upgrade your air compressor? Here are some things you need to consider. …


When it comes to laser cutting and other industrial processes, the choice of assist gas is crucial in achieving optimal results. Nitrogen and oxygen are commonly utilized as assist gases, each with its own unique properties and applications. Understanding the characteristics of both gases, will help you to make an informed decision to ensure precision, efficiency, and cost-effectiveness in your operations. …


Mobile air compressors are portable, towable compressors particularly useful for applications that suit the construction and roading industry! You'll often see a mobile compressor being used for sandblasting, irrigation blow-outs, and for quarrying tools such as pneumatic block cutters and rock drills.Β Β  …


Did you know that Chicago Pneumatic helped man land on the moon? Notice in this photo of the Apollo 11 landing what appear to be "soccer balls" on top of the capsule. They were inflated through a compressor specially developed by Chicago Pneumatic for NASA. …


Your company purchased an air dryer for your compressor, now where should you install it? One of the most common things we see in the industry are air dryers being stored on top of the compressors. Seems like a wasted space not being used on top of the compressor, right? Wrong. …


When using air compressors, there are many variables that are integral to the quality and effectiveness of your compressed air. When dryer air is necessary, being able to constantly and accurately monitor dew points can be a critical factor to your operation. …


Compressed air plays an integral role in breweries both large and small around the world. From start to finish, all details in the brewing process are managed in fine detail and having the right air compressor is no exception. …


We Kiwi's love our Coffee! Coffee, like all other food & beverage products, must go through a preservation process to keep the beans fresh during storage and packaging before they reach the consumer. Coffee that is not properly stored after it is roasted will lose a large amount of carbon dioxide, which lessens its' flavor and speeds up the staling process. One of the most common ways to preserve the freshness of coffee is the use of nitrogen gas. Learn more here: …

Show More