The importance of saving energy when compressing air

For many businesses, preserving energy and becoming more sustainable have become top priorities. That not only saves them money but also makes them more competitive in the future, when demand for “green” products and services will only increase. Not just because governments mandate greater sustainability but also because customers expect it.

Ash Air can help prepare you for that future while making you more competitive right now. That’s because compressed air plays a major role in the drive for greater sustainability. While compressed air has many benefits, compression requires a lot of energy.

Instead of seeing that as a problem, compressed air users should see it as an opportunity for increased sustainability and significant cost savings. Because where a lot of energy is consumed, a lot of energy can be saved.

Traditionally, it has cost a lot more to run a compressor than to purchase it. Energy costs made up 70% (or even more) of the total cost of ownership – much more than the initial investment and upkeep.

However, thanks to modern, energy-saving technologies, it is now possible to greatly reduce how much energy a compressor requires and, therefore, how much you have to spend on it. 

Check out this blog post for more tips on how you can save energy and money.

How Ash Air can help you become more sustainable

Ash Air offers a wide range of products and services that will help you reduce your energy consumption while lowering your operating costs.

It all starts with the compressor itself. Traditional fixed-speed models would simply be switched on and then kept delivering a steady supply of compressed air – whether it was needed or not. Ash Air offers a cost-saving and energy-preserving alternative: The CPVS.

This innovative compressor is equipped with a variable speed drive that only produces as much energy as is required at any time. That can decrease your energy use by 35% or even more. In turn, this will lower your operating costs significantly.

However, it is not just the compressor that is important but also how it is controlled and monitored. Ash Air offers different solutions that allow you to always keep an eye on your equipment to ensure that you get the most out of it.

For example, if you are operating multiple compressors, we have our ECOntrol central controller. It makes your operation more sustainable by increasing its efficiency and reliability. This central controller sends you messages and alerts if the compressor needs your attention. In addition, maintenance scheduling and logs ensure long service lives.

Finally, it helps you save energy by helping you detect costly leaks and other inefficiencies in your system.

But sustainability isn’t just about how your air is compressed, it’s also about what happens to the residual heat this process creates.

Do not let it go to waste. Instead, take advantage of Ash Air's Energy box! Our new energy recovery technology allows you to reuse 80% of the thermal energy produced during compression. For example, you can use that energy for your central heating system or for other industrial processes. 

The right partner for saving energy when compressing air

The final “ingredient” for saving energy when compressing air is not something that shows up in a product portfolio but it is one of the most important.

It is finding the right partner who has the experience and expertise to add real value to your operation. Ash Air is that partner. We have been on the leading edge of developing efficient and sustainable compressed air products and services for many years.

Just get in touch with us and we will show you how you can benefit from our solutions.

Do you have an idea for our #expertcorner? Let us know!

Useful links:

Book Your Compressor Service



Who we are and how Ash Air can help your business!

Ash Air has been around in New Zealand since 1979, and we’ve grown into a nationwide company with international support and a reputation for quality and reliability.We look after all things compressed air for your business!

  • Reciprocating, Screw, air compressors
  • Vacuum pumps
  • Nitrogen
  • An extensive line of air treatment components

Ash Air's range of Chicago Pneumatic, Alup, Pneumatech, and Quincy compressors are used extensively around the world in industries ranging from oil and gas to food, automotive and farming, and we bring you these world class compressors here in the land of the long white cloud.Our technicians are compressed air equipment experts and are dedicated to addressing customer needs. Supported by a 13 locations nationwide, Ash Air offers one of the widest selections of compressed air equipment and parts available today in New Zealand.

Reliability and Efficiency

With Ash Air compressors, you can count on reliability and high performance for even the most demanding applications. We focus our efforts on the following:

  • Increasing uptime
  • Reducing unexpected repairs
  • Reducing energy consumption
  • Improving the cleanliness of compressed air


Talk to the team today:  CONTACT US CONTACT US

Read more from our #expertcorner


Just like any other equipment, a compressed air installation also requires the necessary maintenance work during its entire lifespan. Even though maintenance costs are only about 5 to 10% of a machine's annual operating costs, failure to budget for maintenance can have potentially disastrous consequences. …


The air dyer is one of the most ignored cooler in the system. A dirty condenser will cause water in the lines, or worse it will cause complete dryer failure. …


Using nitrogen is not about fully replacing CO2, but it can reduce their consumption of CO2 by close to 70%. Using nitrogen is about sustainability. Creating your own nitrogen is easy and will reduce the use of a greenhouse gas, which is better for the environment. It will also save you money as early as month one adding that savings to your bottom line. …


A question that is occasionally asked by our customers to Ash Air is 'what is the cost of compressed air?'  This article looks at the product costs involved with compressed air, as well as minimising the energy cost of compressors and cost allocation. When looking at these factors, we need to realise what causes dropped efficiency of your compressor, leading to increased costs of compressed air. …


You may have great fall protection measures in place to keep employees safe when working at height, but what about their co-workers below? Dropped tools and other falling objects are a major hazard – and one that isn’t always fully addressed.  …


Providing a safe working environment for operators is essential, especially when using pneumatic tools and compressed air. If there is a failure in the air network and the hose is not adequately clamped, the resulting whiplash could be devastating. Failure to follow best practice can result in injuries, associated production downtime and decreased productivity. …


A common questions asked is why do I need an air dryer for my compressor? Typically, air compressors produce water, and although the water can be drained, there can still be aerosol and vapour droplets that are present. This is because water cannoet be compressed. Water can damage your compressor by corroding the valves, pipes and machinery controls, which will cost you time and money to resolve. In the long run, the cost of a new compressor is a small price to pay compared to the loss of production that could potentially arise due to water damage in your compressor.





…


Air compressors can fail for an assortment of different reasons: Normal wear and tear, lifespan and age of the unit, poor maintenance, power surge, install issues are just a few the come to mind. Check out this blog to find out our top 7 tips to ensure your compressor is looked after!  …


That cold, rainy, and in some places icey New Zealand winter is upon us, and with the following air compressor tips, your air system will be prepared with the preferred temperatures, despite the weather outside. Regardless of whether or not it actually snows or freezes up where you live, most winterisation service recommendations are also basic, solid maintenance procedures that will help extend the life and operational efficiencies of air compressors regardless of whether you live in Queenstown or Northland. …


If you're wondering what an air compressor actually is, you've come to the right place. Simply, air compressors convert power in to air that is pressurised which is then used to power air tools such as spray guns. Air compressors are used in a wide range of applications, so naturally if you want one that will be designed for spray painting your vehicle, you want a compressor specifically made for spray guns! This way your compressor will be able to provide the right amount of power to perform the job. …


Compressed air plays a fundamental role in industrial activities. Depending on the type of application, the energy cost of producing compressed air can be very high. Below are some tips to save on you compressor bill. …


Air Compressors are essential tools in a variety of industrial settings. No matter what industry you are in having a reliable air compressor can be a crucial part of getting the job done efficiently. However, like an investment, air compressors require upkeep and maintenance, and eventually will need to be upgraded. But how do you know when it’s time to upgrade your air compressor? Here are some things you need to consider. …


When it comes to laser cutting and other industrial processes, the choice of assist gas is crucial in achieving optimal results. Nitrogen and oxygen are commonly utilized as assist gases, each with its own unique properties and applications. Understanding the characteristics of both gases, will help you to make an informed decision to ensure precision, efficiency, and cost-effectiveness in your operations. …


Mobile air compressors are portable, towable compressors particularly useful for applications that suit the construction and roading industry! You'll often see a mobile compressor being used for sandblasting, irrigation blow-outs, and for quarrying tools such as pneumatic block cutters and rock drills.   …


Did you know that Chicago Pneumatic helped man land on the moon? Notice in this photo of the Apollo 11 landing what appear to be "soccer balls" on top of the capsule. They were inflated through a compressor specially developed by Chicago Pneumatic for NASA. …


Your company purchased an air dryer for your compressor, now where should you install it? One of the most common things we see in the industry are air dryers being stored on top of the compressors. Seems like a wasted space not being used on top of the compressor, right? Wrong. …


When using air compressors, there are many variables that are integral to the quality and effectiveness of your compressed air. When dryer air is necessary, being able to constantly and accurately monitor dew points can be a critical factor to your operation. …


Compressed air plays an integral role in breweries both large and small around the world. From start to finish, all details in the brewing process are managed in fine detail and having the right air compressor is no exception. …


We Kiwi's love our Coffee! Coffee, like all other food & beverage products, must go through a preservation process to keep the beans fresh during storage and packaging before they reach the consumer. Coffee that is not properly stored after it is roasted will lose a large amount of carbon dioxide, which lessens its' flavor and speeds up the staling process. One of the most common ways to preserve the freshness of coffee is the use of nitrogen gas. Learn more here: …


Air compressors are helpful for an enormous range of applications such as air filling, packaging, tools, HVAC control, and more! One possible drawback is the amount of electricity they use; air compressors can be a huge drain on energy if used ​inefficiency...  …


We get it, buying an air compressor is a big financial decision. And now we are suggesting that you need two air compressors, not just one. Ask yourself one question- Can your business still run if your air compressor goes down? …


It’s no secret – air compressors are excellent sources of energy. Not only do they power essential manufacturing elements and applications, but the heat generated as a result of the compressed air processes can be used as a byproduct that offsets other energy costs. However, there’s another form of energy that is also a consequence of the air compression process – sound. …


The emergency stop, "e-stop", is for true emergency situations only. When hitting the e-stop, all power is halted from the machine and the unload process isn't achieved. The emergency stop button is intended to help with possibly hazardous situations that are developing. Common conditions of having to use the e-stop is the misuse of the equipment in ways that weren’t intended, predictable failures not addressed or failing to consider all the foreseeable uses of the compressor.
…


We've put together a list of tips for working safely with air compressors in your environment! We recommend that you always read owners manual before running your compressor. The number one cause for repairs and personal injury is improper use. You've got to remember to use eye protection and hearing protection when operating your air compressor and try to avoid using air compressors in a wet area.  …


Air Compressor Installation Tips Installing Your Reliable Air Compressor

So, you've just bought an efficient and reliable ALUP air compressor? Welcome to the world of compressed air. As your partners in compressed air, we will continue to assist you along your journey. We have provided air compressor installation tips to ensure you get the most out of your air compressor.  …


Air dryers remove any condensation from the air compressed by your air compressor. Questions about them? Find answers to the most frequently asked questions here. …


Power tools are a key to productivity in the oil & gas or the metal working industry. Maintenance and production tasks must be carried out efficiently, however intensive use of vibrating power tools, such as grinders, can expose operators... …


Selective soldering with nitrogen is an essential process in the production of printed circuit boards (PCBs). It is used for bonding components to PCBs that could otherwise be damaged if exposed to a lot of heat. Another area of application are mixed-technology circuit boards with layout constraints.  …


Hydrogen is becoming increasingly important as a promising clean energy carrier – especially with a view to a more climate-friendly future. But have you ever wondered what hydrogen actually is and how it is produced? In this article, we look at the basics and technologies used to produce hydrogen and what makes hydrogen a special element. …

Show More