Our offices are closed from the 21st December until 6th January.

Why is a pneumatic grinder spinning too slowly?


Your tool is stalling, or is not working to its expected performance, and you find yourself asking ‘why is my angle grinder spinning too slowly?’, or ‘why has my pneumatic grinder stopped working?’, read on

In this scenario, it’s all too easy to blame the tool itself. However, there are two other fundamental factors that could be causing it to fail – the air line set-up and the maintenance regime – and these are often overlooked.

If your pneumatic angle grinder’s abrasive spin starts to slow down, or the motor stalls when you apply force then this is a tell-tale sign that the tool is not operating at full performance. It is vital to look out for these indicators, otherwise there will be a significant negative impact on productivity.

To try and prevent the tool from stalling, it is common practice to apply less force, but this means more time to complete the job, which results in reduced efficiency. If efficiency is affected, this will have major financial consequences and lead to a decrease in global production.

Let’s take a closer look at the two most common reasons affecting a pneumatic grinder’s performance.

1. Air line set-up & air line accessories

A pneumatic tool’s motor needs two things to work properly and at maximum speed:

  1. A dynamic air pressure of 90 psi / 6.3 bars at the tool inlet 
  2. Air flow as recommended by the tool manufacturer

Without the correct pressure and flow, the tool’s motor will not have enough energy to run the abrasive at full speed, resulting in a suboptimal efficiency (for rated speed, always check the abrasive manufacturer’s recommended speed).

How to get the right dynamic air pressure and air flow?

The choice of the right air line accessories (such as hose, couplings, FRL) is critical to ensure your tool’s performance. To demonstrate how performance can be affected, we have set up a CP3650 industrial pneumatic grinder with two different hose set-ups:

  1. One with the manufacturer recommended hose diameter (in this case: ½”) 
  2. One with a smaller hose diameter (in this case: 3/8”)

See the difference in performance for yourself – it’s astounding!

To ensure accessories fit the tool perfectly and deliver the best performance level, always refer to the tool manufacturer’s recommendations. There are four key values to consider when selecting your air line accessories:

  1. air line size, 
  2. air inlet type, 
  3. maximum air consumption at load, 
  4. recommended hose diameter/length.

To get tips on making sure you have the right air line set-up and good habits (such as air lubrication), download our guide Is your air tool installation right? This guide includes a valuable check list to help you do your own air line set-up evaluation.

2. Tools maintenance

Just as you would perform regular maintenance on your car, it is vital to carry out routine maintenance on your tools – to ensure they are kept in excellent working condition, and delivering a consistent high performance. After all, pneumatic tools are mechanical systems comprising wear parts that need regular inspection and changes (as required).

The parts that wear most frequently in pneumatic industrial grinders, and need regular maintenance are:

  1. Blades, with inspection recommended every 500 h
  2. Bevel gears (angle grinders and sanders only), with the maintenance interval specified as every 1000 to 2000h depending on the tools

Browse our tools and shop online

View 5 Products

Grinders & Sanders

For maximum material removal with minimum effort and high-quality finish, Chicago Pneumatic delivers robust, durable and lightweight easy-to-handle tools.

Surface applications from heavy material removal to fine finishing. Tools designed to bring better comfort and increase your productivity. The range provides random orbital sanders, rotary sanders, pistol sander & polishers, and belt sanders. Secure payment, Afterpay, nationwide delivery. Buy now, pay layer.

View 4 Products

Percussive Tools & Drills

Their combination of power, compactness and light weight gets the job done. Better operator comfort comes with a unique vibration dampening body.
The range provides industrial chipping hammers, weld flux chippers, needle scalers, long reach scalers and rust & weld scalers.

With drilling capacity from 6mm (1/4”) to 50mm (2”), various speeds and power, our drills are designed to handle both your tough and smooth operations. The range provides straight, angle and pistol drills. Secure payment, Afterpay, nationwide delivery. Buy now, pay layer.

View 13 Products

Specialty & Cutting

The range provides saws, high speed cutters, nibblers, shears, engraving pens, riveters, caulking guns, air files, and blow guns. Secure payment, Afterpay, nationwide delivery. Buy now, pay layer.

View 7 Products

Staplers & Brad Nailers

The perfect solution for all your nailing needs, from framing to decking and more. Our range of professional-grade brad nailers offer precision and durability to ensure you get the best results possible. As a professional tradesperson, our brad nailers are the ideal choice for any nailing task.

Explore our range of staple guns. Our brand of PIT TOOLS by Ash Air heavy-duty staplers we supply are trusted by tradespeople all over NZ.

Our Brad nailers and Staplers are suitable for a range of applications: Bedding and furniture, Cabinets and joinery, Fencing, Framing, Prefab housing, Wall lining, floor covering, cabinet making, trellis and boxes, interior decorative trim, cabinetry, cabinet backing, crafts and hobbies.

View 7 Products

Wrenches

The use of the latest technologies and materials, such as composite housing or steel housing for the toughest materials, makes CP Industrial impacts the best in each class. Our versatile line features different clutches such as rocking dog, 2 jaw, pin, single dog or twin dog clutches.

We offer a range of powerful pneumatic ratchet wrenches from ¼’ to ½” square drive for every task.
Due to their small size and light weight, pneumatic ratchets are an excellent choice for fastening in tight or cumbersome applications. Secure payment, Afterpay, nationwide delivery. Buy now, pay layer.

Do you have an idea for our #expertcorner? Let us know!

Useful links:

Book your Service here

Browse our Services here

Browse our Products here

Browse our News corner here

Browse our Sustainability focus here



Who we are and how Ash Air can help your business!

Ash Air has been around in New Zealand since 1979, and we’ve grown into a nationwide company with international support and a reputation for quality and reliability.We look after all things compressed air for your business!

  • Rotary Screw and Piston Air Compressors
  • Vacuum Pumps and Blowers
  • Nitrogen Generation
  • An extensive line of Air Treatment components
  • AIRnet Piping System and  Filtration
  • Mobile Compressors, Generators, and Light Towers

Ash Air's range of Chicago Pneumatic, ALUP, Pneumatech, and Atlas Copco products are used extensively around the world in industries ranging from oil and gas to food, automotive and farming, and we bring you these world-class compressors here in the land of the long white cloud.Our technicians are compressed air equipment experts and are dedicated to addressing customer needs. Supported with nationwide coverage, Ash Air offers one of the widest selections of compressed air, vacuum pump, and industrial gas equipment and parts available today in New Zealand.

Reliability and Efficiency

With Ash Air, you can count on reliability and high performance for even the most demanding applications. We focus our efforts on the following:

  • Increasing uptime
  • Reducing unexpected repairs
  • Reducing energy consumption and meeting our sustainability goals
  • Improving the cleanliness of compressed air


Talk to the team today:  CONTACT US CONTACT US

Read more from our #expertcorner


Just like any other equipment, a compressed air installation also requires the necessary maintenance work during its entire lifespan. Even though maintenance costs are only about 5 to 10% of a machine's annual operating costs, failure to budget for maintenance can have potentially disastrous consequences. …


The air dyer is one of the most ignored cooler in the system. A dirty condenser will cause water in the lines, or worse it will cause complete dryer failure. …


Using nitrogen is not about fully replacing CO2, but it can reduce their consumption of CO2 by close to 70%. Using nitrogen is about sustainability. Creating your own nitrogen is easy and will reduce the use of a greenhouse gas, which is better for the environment. It will also save you money as early as month one adding that savings to your bottom line. …


A question that is occasionally asked by our customers to Ash Air is 'what is the cost of compressed air?'  This article looks at the product costs involved with compressed air, as well as minimising the energy cost of compressors and cost allocation. When looking at these factors, we need to realise what causes dropped efficiency of your compressor, leading to increased costs of compressed air. …


You may have great fall protection measures in place to keep employees safe when working at height, but what about their co-workers below? Dropped tools and other falling objects are a major hazard – and one that isn’t always fully addressed.  …


Providing a safe working environment for operators is essential, especially when using pneumatic tools and compressed air. If there is a failure in the air network and the hose is not adequately clamped, the resulting whiplash could be devastating. Failure to follow best practice can result in injuries, associated production downtime and decreased productivity. …


A common questions asked is why do I need an air dryer for my compressor? Typically, air compressors produce water, and although the water can be drained, there can still be aerosol and vapour droplets that are present. This is because water cannoet be compressed. Water can damage your compressor by corroding the valves, pipes and machinery controls, which will cost you time and money to resolve. In the long run, the cost of a new compressor is a small price to pay compared to the loss of production that could potentially arise due to water damage in your compressor.





…


Air compressors can fail for an assortment of different reasons: Normal wear and tear, lifespan and age of the unit, poor maintenance, power surge, install issues are just a few the come to mind. Check out this blog to find out our top 7 tips to ensure your compressor is looked after!  …


That cold, rainy, and in some places icey New Zealand winter is upon us, and with the following air compressor tips, your air system will be prepared with the preferred temperatures, despite the weather outside. Regardless of whether or not it actually snows or freezes up where you live, most winterisation service recommendations are also basic, solid maintenance procedures that will help extend the life and operational efficiencies of air compressors regardless of whether you live in Queenstown or Northland. …


If you're wondering what an air compressor actually is, you've come to the right place. Simply, air compressors convert power in to air that is pressurised which is then used to power air tools such as spray guns. Air compressors are used in a wide range of applications, so naturally if you want one that will be designed for spray painting your vehicle, you want a compressor specifically made for spray guns! This way your compressor will be able to provide the right amount of power to perform the job. …


Compressed air plays a fundamental role in industrial activities. Depending on the type of application, the energy cost of producing compressed air can be very high. Below are some tips to save on you compressor bill. …


Air Compressors are essential tools in a variety of industrial settings. No matter what industry you are in having a reliable air compressor can be a crucial part of getting the job done efficiently. However, like an investment, air compressors require upkeep and maintenance, and eventually will need to be upgraded. But how do you know when it’s time to upgrade your air compressor? Here are some things you need to consider. …


When it comes to laser cutting and other industrial processes, the choice of assist gas is crucial in achieving optimal results. Nitrogen and oxygen are commonly utilized as assist gases, each with its own unique properties and applications. Understanding the characteristics of both gases, will help you to make an informed decision to ensure precision, efficiency, and cost-effectiveness in your operations. …


Mobile air compressors are portable, towable compressors particularly useful for applications that suit the construction and roading industry! You'll often see a mobile compressor being used for sandblasting, irrigation blow-outs, and for quarrying tools such as pneumatic block cutters and rock drills.   …


Did you know that Chicago Pneumatic helped man land on the moon? Notice in this photo of the Apollo 11 landing what appear to be "soccer balls" on top of the capsule. They were inflated through a compressor specially developed by Chicago Pneumatic for NASA. …


Your company purchased an air dryer for your compressor, now where should you install it? One of the most common things we see in the industry are air dryers being stored on top of the compressors. Seems like a wasted space not being used on top of the compressor, right? Wrong. …


When using air compressors, there are many variables that are integral to the quality and effectiveness of your compressed air. When dryer air is necessary, being able to constantly and accurately monitor dew points can be a critical factor to your operation. …


Compressed air plays an integral role in breweries both large and small around the world. From start to finish, all details in the brewing process are managed in fine detail and having the right air compressor is no exception. …


We Kiwi's love our Coffee! Coffee, like all other food & beverage products, must go through a preservation process to keep the beans fresh during storage and packaging before they reach the consumer. Coffee that is not properly stored after it is roasted will lose a large amount of carbon dioxide, which lessens its' flavor and speeds up the staling process. One of the most common ways to preserve the freshness of coffee is the use of nitrogen gas. Learn more here: …


Air compressors are helpful for an enormous range of applications such as air filling, packaging, tools, HVAC control, and more! One possible drawback is the amount of electricity they use; air compressors can be a huge drain on energy if used ​inefficiency...  …


We get it, buying an air compressor is a big financial decision. And now we are suggesting that you need two air compressors, not just one. Ask yourself one question- Can your business still run if your air compressor goes down? …


It’s no secret – air compressors are excellent sources of energy. Not only do they power essential manufacturing elements and applications, but the heat generated as a result of the compressed air processes can be used as a byproduct that offsets other energy costs. However, there’s another form of energy that is also a consequence of the air compression process – sound. …


The emergency stop, "e-stop", is for true emergency situations only. When hitting the e-stop, all power is halted from the machine and the unload process isn't achieved. The emergency stop button is intended to help with possibly hazardous situations that are developing. Common conditions of having to use the e-stop is the misuse of the equipment in ways that weren’t intended, predictable failures not addressed or failing to consider all the foreseeable uses of the compressor.
…

Show More