How to Efficiently Dry Compressed Air

Liquid water in compressed-air systems can lead to rusted equipment and unresponsive controls. Anyone who uses compressed air will, at some point, find liquid water in the air distribution system. This can be anything from a nuisance to a serious problem, depending on the application. If water might corrode equipment or introduce bacteria, removing it is critical.

Compressed air typically contains water as both liquid and vapor. Because removing it carries a cost, it’s important to define how dry the air must be for a given application and specify the right equipment to produce this result. First, though, it’s helpful to understand the source of water in a system.

Why and how do we dry compressed air?

Atmospheric air contains more water vapor at high temperatures and less at lower temperatures. This has an effect on the water concentration when the air is compressed. For example, a compressor with a working pressure of 7 bar and a capacity of 200 l/s that compresses air at 20ËšC with a relative humidity of 80% will release 10 liters/hour of water in the compressed air line. Problems and disturbances can occur due to water precipitation in the pipes and connected equipment. To avoid this, the compressed air must be dried.

What is pressure dew point?

The term "pressure dew point" (PDP) is used to describe the water content in the compressed air. It is the temperature at which water vapor condenses into water at the current working pressure. Low PDP values indicate small amounts of water vapor in the compressed air.

It is important to remember that atmospheric dew point can not be compared with PDP when comparing different dryers. For example, a PDP of +2˚C at 7 bar is equivalent to –23˚C at atmospheric pressure. To use a filter to remove moisture (lower the dew point) does not work. This is because further cooling leads to continued precipitation of condensation water.

You can select the main type of drying equipment based on the pressure dew point. When taking cost into account, the lower the dew point required, the higher the investment and operating costs for air drying. Five techniques exist for removing the moisture from compressed air: cooling plus separation, over-compression, membranes, absorption and adsorption drying.

How to dispose of the condensate after drying the air?

Anyone who runs a compressed air system (using oil-injected technology) needs to be aware of how to properly dispose of the condensate in a responsible manner, so as not to infringe any environmental laws. The condensate released by compressed air equipment will have tiny particles of oil in that are not visible to the naked eye, which is why it needs proper disposal. Not only is incorrect disposal detrimental to the environment, but you could also incur a fine and damage to your reputation as a responsible company.

There are many rules concerning the disposal of waste generally, as you will no doubt be aware if you have paid a recent visit to your local recycling centre and compared that to a visit only a few years ago. Don’t let your compressed air supply catch you out without doing a fairly easy first check.

Have a walk around your compressed air equipment: you should be able to see the condensate drains appearing from the back of the compressors and dryers on your site. Take a look at where these are piped to. Ideally you should see them all going to an oil/water separator of some description and then off to a foul drain. If they are going straight from a drain onto the floor or just into a standard plastic container then this should raise a red flag. Oil/water separators are very easy to install. Note that there are many rules around the disposal of condensate, even with the correct equipment in place, and the rules can vary from region to region.

 

Talk to New Zealand's compressed air experts:

If you are having issues with your compressed air system, don't hesitate to get in touch with the team at Ash Air. With coverage over all regions throughout the country, over 100 staff, and hundreds of years of combined experience, you can count on us to deliver second-to-none service and sustainable solutions that increase customer productivity.

See the services we offer here

And get in touch today! 

Do you have an idea for our #expertcorner? Let us know!

Useful links:

Book Your Compressor Service

Who we are and how Ash Air can help your business!

Ash Air has been around in New Zealand since 1979, and we’ve grown into a nationwide company with international support and a reputation for quality and reliability.We look after all things compressed air for your business!

  • Reciprocating, Screw, air compressors
  • Vacuum pumps
  • Nitrogen
  • An extensive line of air treatment components

Ash Air's range of Chicago Pneumatic, Alup, Pneumatech, and Quincy compressors are used extensively around the world in industries ranging from oil and gas to food, automotive and farming, and we bring you these world class compressors here in the land of the long white cloud.Our technicians are compressed air equipment experts and are dedicated to addressing customer needs. Supported by a 13 locations nationwide, Ash Air offers one of the widest selections of compressed air equipment and parts available today in New Zealand.

Reliability and Efficiency

With Ash Air compressors, you can count on reliability and high performance for even the most demanding applications. We focus our efforts on the following:

  • Increasing uptime
  • Reducing unexpected repairs
  • Reducing energy consumption
  • Improving the cleanliness of compressed air


Talk to the team today:  CONTACT US CONTACT US

Read more from our #expertcorner


Just like any other equipment, a compressed air installation also requires the necessary maintenance work during its entire lifespan. Even though maintenance costs are only about 5 to 10% of a machine's annual operating costs, failure to budget for maintenance can have potentially disastrous consequences. …


The air dyer is one of the most ignored cooler in the system. A dirty condenser will cause water in the lines, or worse it will cause complete dryer failure. …


Using nitrogen is not about fully replacing CO2, but it can reduce their consumption of CO2 by close to 70%. Using nitrogen is about sustainability. Creating your own nitrogen is easy and will reduce the use of a greenhouse gas, which is better for the environment. It will also save you money as early as month one adding that savings to your bottom line. …


A question that is occasionally asked by our customers to Ash Air is 'what is the cost of compressed air?'  This article looks at the product costs involved with compressed air, as well as minimising the energy cost of compressors and cost allocation. When looking at these factors, we need to realise what causes dropped efficiency of your compressor, leading to increased costs of compressed air. …


You may have great fall protection measures in place to keep employees safe when working at height, but what about their co-workers below? Dropped tools and other falling objects are a major hazard – and one that isn’t always fully addressed.  …


Providing a safe working environment for operators is essential, especially when using pneumatic tools and compressed air. If there is a failure in the air network and the hose is not adequately clamped, the resulting whiplash could be devastating. Failure to follow best practice can result in injuries, associated production downtime and decreased productivity. …


A common questions asked is why do I need an air dryer for my compressor? Typically, air compressors produce water, and although the water can be drained, there can still be aerosol and vapour droplets that are present. This is because water cannoet be compressed. Water can damage your compressor by corroding the valves, pipes and machinery controls, which will cost you time and money to resolve. In the long run, the cost of a new compressor is a small price to pay compared to the loss of production that could potentially arise due to water damage in your compressor.





…


Air compressors can fail for an assortment of different reasons: Normal wear and tear, lifespan and age of the unit, poor maintenance, power surge, install issues are just a few the come to mind. Check out this blog to find out our top 7 tips to ensure your compressor is looked after!  …


That cold, rainy, and in some places icey New Zealand winter is upon us, and with the following air compressor tips, your air system will be prepared with the preferred temperatures, despite the weather outside. Regardless of whether or not it actually snows or freezes up where you live, most winterisation service recommendations are also basic, solid maintenance procedures that will help extend the life and operational efficiencies of air compressors regardless of whether you live in Queenstown or Northland. …


If you're wondering what an air compressor actually is, you've come to the right place. Simply, air compressors convert power in to air that is pressurised which is then used to power air tools such as spray guns. Air compressors are used in a wide range of applications, so naturally if you want one that will be designed for spray painting your vehicle, you want a compressor specifically made for spray guns! This way your compressor will be able to provide the right amount of power to perform the job. …


Compressed air plays a fundamental role in industrial activities. Depending on the type of application, the energy cost of producing compressed air can be very high. Below are some tips to save on you compressor bill. …


Air Compressors are essential tools in a variety of industrial settings. No matter what industry you are in having a reliable air compressor can be a crucial part of getting the job done efficiently. However, like an investment, air compressors require upkeep and maintenance, and eventually will need to be upgraded. But how do you know when it’s time to upgrade your air compressor? Here are some things you need to consider. …


When it comes to laser cutting and other industrial processes, the choice of assist gas is crucial in achieving optimal results. Nitrogen and oxygen are commonly utilized as assist gases, each with its own unique properties and applications. Understanding the characteristics of both gases, will help you to make an informed decision to ensure precision, efficiency, and cost-effectiveness in your operations. …


Mobile air compressors are portable, towable compressors particularly useful for applications that suit the construction and roading industry! You'll often see a mobile compressor being used for sandblasting, irrigation blow-outs, and for quarrying tools such as pneumatic block cutters and rock drills.   …


Did you know that Chicago Pneumatic helped man land on the moon? Notice in this photo of the Apollo 11 landing what appear to be "soccer balls" on top of the capsule. They were inflated through a compressor specially developed by Chicago Pneumatic for NASA. …


Your company purchased an air dryer for your compressor, now where should you install it? One of the most common things we see in the industry are air dryers being stored on top of the compressors. Seems like a wasted space not being used on top of the compressor, right? Wrong. …

Show More