What Does Commissioning your Air Compressor Mean?

Air Compressor Commissioning & Installation Services

The definition of Commissioning from Compressed Air Best Practice magazine, “Compressed air system commissioning is the process for measuring, testing, adjusting, and documenting that the performance of an entire compressed air system achieves the target system efficiencies (scfm/kW as a whole and for each piece of equipment) in all load regimes and potential failure modes.”

Proper compressor installation and commissioning helps ensure trouble-free startup and long-term reliability. Thorough inspection and critical review during each phase of the installation process eliminates “built-in” deficiencies or problems which could later result in equipment failures or poor performance.

Commissioning: Start with the Preparation

Checking your air compressor before the installation is critical to its' success. The checklists in the below sections are intended to aid in this inspection/review process, but refer to your manufacturer's instruction manual for exact details.

Installation Checks

Reverse Rotation Check

This is probably the single most important startup item that should be conducted before starting the compressor.

The compressor should be “bump started” (i.e. control power de-energized immediately after startup) and the direction of the pressure gauge movement should be checked to insure that the discharge pressure rises upon compressor start. If the compressor rotation is backwards the discharge pressure will be pulled immediately into a vacuum, on a rotary unit this will starve the air-end of needed oil and cause air-end damage within a seconds. If the rotation is backwards, the phasing of the compressor should be corrected (reversing any two leads will change rotation) before attempting to re-start the compressor.

Some 3 phase units come with a piece of paper taped to the top of the cabinet. If the electrical phases are correct when started it will blow the paper up revealing an OK on the bottom, this indicates the rotation is correct. In cases the phases are out of sequence when started air will be pulled into the cabinet sucking the paper down, this would indicate incorrect phase sequence and wrong motor rotation and would need corrected immediately before restarting.

Start-Up Of the Compressor

Great news, your pre-commissioning is all set. Now is time for installation and the next round of commissioning checklists. Below are a few things to keep in mind during start up.

Startup Check List

Do you have an idea for our #expertcorner? Let us know!

Useful links:

Book Your Compressor Service



Who we are and how Ash Air can help your business!

Ash Air has been around in New Zealand since 1979, and we’ve grown into a nationwide company with international support and a reputation for quality and reliability.We look after all things compressed air for your business!

  • Reciprocating, Screw, air compressors
  • Vacuum pumps
  • Nitrogen
  • An extensive line of air treatment components

Ash Air's range of Chicago Pneumatic, Alup, Pneumatech, and Quincy compressors are used extensively around the world in industries ranging from oil and gas to food, automotive and farming, and we bring you these world class compressors here in the land of the long white cloud.Our technicians are compressed air equipment experts and are dedicated to addressing customer needs. Supported by a 13 locations nationwide, Ash Air offers one of the widest selections of compressed air equipment and parts available today in New Zealand.

Reliability and Efficiency

With Ash Air compressors, you can count on reliability and high performance for even the most demanding applications. We focus our efforts on the following:

  • Increasing uptime
  • Reducing unexpected repairs
  • Reducing energy consumption
  • Improving the cleanliness of compressed air


Talk to the team today:  CONTACT US CONTACT US

Read more from our #expertcorner


Just like any other equipment, a compressed air installation also requires the necessary maintenance work during its entire lifespan. Even though maintenance costs are only about 5 to 10% of a machine's annual operating costs, failure to budget for maintenance can have potentially disastrous consequences. …


The air dyer is one of the most ignored cooler in the system. A dirty condenser will cause water in the lines, or worse it will cause complete dryer failure. …


Using nitrogen is not about fully replacing CO2, but it can reduce their consumption of CO2 by close to 70%. Using nitrogen is about sustainability. Creating your own nitrogen is easy and will reduce the use of a greenhouse gas, which is better for the environment. It will also save you money as early as month one adding that savings to your bottom line. …


A question that is occasionally asked by our customers to Ash Air is 'what is the cost of compressed air?'  This article looks at the product costs involved with compressed air, as well as minimising the energy cost of compressors and cost allocation. When looking at these factors, we need to realise what causes dropped efficiency of your compressor, leading to increased costs of compressed air. …


You may have great fall protection measures in place to keep employees safe when working at height, but what about their co-workers below? Dropped tools and other falling objects are a major hazard – and one that isn’t always fully addressed.  …


Providing a safe working environment for operators is essential, especially when using pneumatic tools and compressed air. If there is a failure in the air network and the hose is not adequately clamped, the resulting whiplash could be devastating. Failure to follow best practice can result in injuries, associated production downtime and decreased productivity. …


A common questions asked is why do I need an air dryer for my compressor? Typically, air compressors produce water, and although the water can be drained, there can still be aerosol and vapour droplets that are present. This is because water cannoet be compressed. Water can damage your compressor by corroding the valves, pipes and machinery controls, which will cost you time and money to resolve. In the long run, the cost of a new compressor is a small price to pay compared to the loss of production that could potentially arise due to water damage in your compressor.





…


Air compressors can fail for an assortment of different reasons: Normal wear and tear, lifespan and age of the unit, poor maintenance, power surge, install issues are just a few the come to mind. Check out this blog to find out our top 7 tips to ensure your compressor is looked after!  …


That cold, rainy, and in some places icey New Zealand winter is upon us, and with the following air compressor tips, your air system will be prepared with the preferred temperatures, despite the weather outside. Regardless of whether or not it actually snows or freezes up where you live, most winterisation service recommendations are also basic, solid maintenance procedures that will help extend the life and operational efficiencies of air compressors regardless of whether you live in Queenstown or Northland. …

Show More