Why is the quality of the desiccant in my adsorption dryer important?

Why is the quality of the desiccant in my adsorption dryer important?

Adsorption dryers can only be energy efficient if they contain premium desiccant material. The desiccant used in Pneumatech adsorption dryers is carefully selected from a wide range of European and North-American suppliers, based on following key selection criteria:

Crushing strength

Desiccant is subject to continuous cyclic load. Due to this load, low-quality desiccant will easily break up resulting in small dust particles, hereby quickly losing its water attraction capabilities, blocking valves or clogging the downstream dust filter and silencer.

Water resistance

Standard desiccant will degrade when it comes in contact with liquid water. Although a water separator should be installed upstream of an adsorption dryer, some water carry-over to the lower part of the adsorption dryer can never be excluded. All Pneumatech adsorption dryers are therefore equipped with water-resistant desiccant material in the bottom part of the vessel.

Lowest total cost of ownership

We carefully balance initial capital investment with ongoing running cost. Silica gel has the highest adsorption capacity and is therefore used in heat regenerated adsorption dryers (PE & PB). In the dynamic operation conditions of heatless adsorption dryers (PH) only a small percentage of the total static adsorption capacity is used because of the relatively short cycle times. The use of silica gel in the case of -40°C/-40°F PDP applications would increase the initial investment significantly, but would not bring any purge loss reduction or other benefits. Heatless adsorption dryers are therefore filled with activated alumina3 which provide equal dew point requirements (-40°C/-40°F PDP) and energy efficiency at lower investment costs.

³Exception is the PH2-45 which makes use of molecular sieves. 4NWR: non water resistant 5WR: water resistant


Contact us to learn more about our products  Contact us to learn more about our products 


Do you have an idea for our #expertcorner? Let us know!

Useful links:

Book Your Compressor Service

Who we are and how Ash Air can help your business!

Ash Air has been around in New Zealand since 1979, and we’ve grown into a nationwide company with international support and a reputation for quality and reliability.We look after all things compressed air for your business!

  • Reciprocating, Screw, air compressors
  • Vacuum pumps
  • Nitrogen
  • An extensive line of air treatment components

Ash Air's range of Chicago Pneumatic, Alup, Pneumatech, and Quincy compressors are used extensively around the world in industries ranging from oil and gas to food, automotive and farming, and we bring you these world class compressors here in the land of the long white cloud.Our technicians are compressed air equipment experts and are dedicated to addressing customer needs. Supported by a 13 locations nationwide, Ash Air offers one of the widest selections of compressed air equipment and parts available today in New Zealand.

Reliability and Efficiency

With Ash Air compressors, you can count on reliability and high performance for even the most demanding applications. We focus our efforts on the following:

  • Increasing uptime
  • Reducing unexpected repairs
  • Reducing energy consumption
  • Improving the cleanliness of compressed air


Talk to the team today:  CONTACT US CONTACT US

Read more from our #expertcorner


Just like any other equipment, a compressed air installation also requires the necessary maintenance work during its entire lifespan. Even though maintenance costs are only about 5 to 10% of a machine's annual operating costs, failure to budget for maintenance can have potentially disastrous consequences. …


The air dyer is one of the most ignored cooler in the system. A dirty condenser will cause water in the lines, or worse it will cause complete dryer failure. …


Using nitrogen is not about fully replacing CO2, but it can reduce their consumption of CO2 by close to 70%. Using nitrogen is about sustainability. Creating your own nitrogen is easy and will reduce the use of a greenhouse gas, which is better for the environment. It will also save you money as early as month one adding that savings to your bottom line. …


A question that is occasionally asked by our customers to Ash Air is 'what is the cost of compressed air?'  This article looks at the product costs involved with compressed air, as well as minimising the energy cost of compressors and cost allocation. When looking at these factors, we need to realise what causes dropped efficiency of your compressor, leading to increased costs of compressed air. …


You may have great fall protection measures in place to keep employees safe when working at height, but what about their co-workers below? Dropped tools and other falling objects are a major hazard – and one that isn’t always fully addressed.  …


Providing a safe working environment for operators is essential, especially when using pneumatic tools and compressed air. If there is a failure in the air network and the hose is not adequately clamped, the resulting whiplash could be devastating. Failure to follow best practice can result in injuries, associated production downtime and decreased productivity. …


A common questions asked is why do I need an air dryer for my compressor? Typically, air compressors produce water, and although the water can be drained, there can still be aerosol and vapour droplets that are present. This is because water cannoet be compressed. Water can damage your compressor by corroding the valves, pipes and machinery controls, which will cost you time and money to resolve. In the long run, the cost of a new compressor is a small price to pay compared to the loss of production that could potentially arise due to water damage in your compressor.





…

Show More